ELASTOPHENE® FLAM 25 AR T3 is a SBS elastomeric bitumen waterproofing membrane with a glass grid / glass fleece reinforcement. The topside is protected . ELASTOPHENE® 25 AR must be applied by torch-on techniques on a weldable underlayer (FLAM) or bonded with bitumen (EAC free of oxidized bitumen) on a. ELASTOPHENE® FLAM is a flexible SBS elastomeric bitumen waterproofing membrane with a non-woven polyester reinforcement. Both sides are.
|Published (Last):||28 October 2015|
|PDF File Size:||6.80 Mb|
|ePub File Size:||9.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
If there is a risk of rain, then the Knauf Thane ET glued to the first layer must be entirely enclosed by the second layer, even if this means performing work not needed flm the final waterproofing. Removal of remnants of previous waterproofing. The Elastophene 25 is rolled out and cut to fit. Because there elastopene few right angles, there are lots of triangles to be filled in. This second layer of bitumen should be placed on the Knauf Thane ET within a few hours to ensure that the Sopracolle glue speads out under the pressure of the layer of bitumen above.
Since the new waterproofing and the insulation will raise the roof, the rainwater drains must also be raised. The figure shows the three layers and the sidewall elsstophene for each layer. The rain water collector is positioned through a hole cut in the sidewall reinforcement, and then heated to glue it elastophnee the sidewall. On my roof, the rolls of the final layer are positioned north-south, so the second layer must fkam east-west.
Applying the insulation requires careful attention to the weather forecast and the planning of the work. The third bitumous layer is a reinforced bitumen with its lower face covered by a film which melts when heated, gluing it to the second layer.
Fitting the 2nd layer in front of the future rain collector. Pas une goute n’entre dans la maison.
SOPRALENE FLAM JARDIN
The collector is trimmed before applying the outer reinforcement. The photos on this page describe the work. Click on figure to enlarge.
The two layers should be perpendicular to one another. Heating the outer-reinforcement and the collector. Soudage du renfort sur platine et dalle.
ELASTOPHENE® FLAM 70-25
The orientation of the second layer depends on the way in which the third layer elsatophene be applied. L’isolation Knauf Thane ET. Finishing around rain water collector See 2.
The rain water collector will pass through this. Last drops of the weekend’s heavy rain.
ELASTOPHENE® FLAM – Soprema
The weekend brings heavy rain to test the waterproofing — not a drop gets through to the house. Reinforcement at junction of standups.
Cinq points de Sopracolle elaxtophene plaque.
Good waterproofing requires a reinforcing piece between the roof and the wall. Il est bien plus rapide de remplacer les renforts par le flashing: The work specified by this standard is often referred to as Three layers plus insulation, with heated reinforcement. Click on photo to enlarge.
The time has come to re-do the waterproofing on the terrace roof of my house. The first layer and the sidewall reinforcement are complete after 4 days. Finition autour de la platine. These are ajusted now but will be fitted later taking into account the future height of the finished surface. As with the 1st layer, the joint of the flat roof and the rising walls that surround the roof are a possible source of leaks. Bitumous glue is applied to the rising side walls.
ELASTOPHENE® FLAM 25 – Soprema
Before work begins, the existing concrete surface was cleaned with a high pressure bar hose equipped with a rotating jet. For example the first layer could be omitted, and the insulation glued directly to the existing surface. Creative Commons Attribution – NoDerivs 3. Before the insulation is laid, the channels carrying elastophee rain water are reinforced: Cliquer sur les photos pour les agrandir. Welding the outer reinforcement onto the collector. Rodolphe Ferracane, e-mail contact AFR-etancheite.
When reading estimates for waterproofing on flat roofs you may find that the estimate is lightened to reduce the price. It prevents water vapour reaching the insulation, and serves as a base for the finishing layer.
The first layer, which provides the waterproofing, is of elastic bitumen, 2. Cutting nord end of a roll of finishing layer.
Click on the photos to enlarge them. The top serface is covered with flakes of stone which protect it against the ultra-violet.
Creative Commons Attribution – Pas de Modification 3.